What is thermal conductivity, and why do some materials feel colder than others?

Science of WarmthUpdated 4 min read

Thermal conductivity is a measure of how readily heat passes through a material, given in watts per meter per kelvin (W/m·K). Metals have high values and pass heat quickly. Still air and the insulation built around it have very low values, which is why they keep you warm.

What does the number mean?

Picture a slab of material one meter thick with one side 1 °C warmer than the other. The thermal conductivity is the number of watts that flow through each square meter of it. Copper passes about 400 W. Still air passes about 0.026 W. The difference is a factor of more than ten thousand.

Thermal conductivity of common materials

MaterialThermal conductivity, W/m·K
CopperAbout 400
AluminumAbout 205 to 237
Carbon steelAbout 45 to 55
Stainless steelAbout 15
GlassAbout 1
WaterAbout 0.6
Human skin and fatAbout 0.2 to 0.4
WoodAbout 0.1 to 0.2
Wool and polyester insulationAbout 0.035 to 0.05
Closed-cell foamAbout 0.03 to 0.04
Still airAbout 0.026
Silica aerogel compositesAbout 0.013 to 0.02

Values are approximate at room temperature and vary with composition, density and moisture.

Why does metal feel colder than wood?

A metal bench and a wooden bench in the same room are at the same temperature. The metal feels colder because it carries heat away from your skin faster. Your skin senses its own temperature dropping and reports cold. Touch tells you about heat flow, not about the temperature of the object.

Why is still air such a good insulator?

Gas molecules are far apart, so they pass energy between them slowly. The catch is the word still. Moving air carries heat by convection, which is far faster. Insulation works by trapping air in spaces too small for it to circulate. Fleece, down, foam and fiberglass are all ways of holding air still.

Why does wet clothing feel so cold?

Water conducts heat about 23 times better than air. When water replaces the air in a fabric, the fabric’s insulation collapses. Evaporation then takes more heat. This is why staying dry matters so much in the cold.

Conductivity, resistance and thickness

Conductivity is a property of the material. How well a layer insulates also depends on how thick it is.

Thermal resistance equals thickness divided by conductivity.

A 10 mm layer of foam with a conductivity of 0.035 W/m·K has a resistance of 0.29 m²·K/W. Doubling the thickness doubles the resistance. Halving the conductivity does the same. Clothing insulation in clo and building insulation in R-value are both measures of thermal resistance. See clo value explained.

Can anything beat still air?

Yes. Aerogels have pores so small that air molecules collide with the pore walls more often than with each other, which suppresses conduction through the gas. Vacuum panels remove the gas altogether. See aerogel clothing insulation.

Key takeaways

  • Thermal conductivity describes how readily a material passes heat.
  • Metals conduct heat thousands of times better than air.
  • Insulation is mostly trapped, still air.
  • Water conducts far better than air, so wet insulation fails.
  • A layer’s insulating value is its thickness divided by its conductivity.

FAQ

What is the unit of thermal conductivity?

Watts per meter per kelvin, written W/m·K. In older U.S. references it appears as BTU per hour per foot per degree Fahrenheit.

Is a lower or higher thermal conductivity better for insulation?

Lower. A low value means heat passes slowly.

What material has the lowest thermal conductivity?

Among practical solids, silica aerogels, at roughly 0.013 to 0.02 W/m·K. Vacuum insulation panels are lower still because they remove the air.

Does thermal conductivity change with temperature?

Yes, modestly for most materials over everyday ranges. Air’s conductivity rises slightly as it warms.

Is thermal conductivity the same as R-value?

No. Conductivity is a property of a material. R-value is the resistance of a specific thickness of it.

Sources

  1. Incropera, DeWitt, Bergman and Lavine, Fundamentals of Heat and Mass Transfer (Wiley)
  2. ASHRAE Handbook: Fundamentals, thermal properties of materials
  3. ASTM C518, Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
  4. CRC Handbook of Chemistry and Physics, thermal conductivity tables